SOLVENT IMAGE REMOVER "SOLVENT KESHIRON"
 |
|||
| Order code No. | Size | Package | |
|---|---|---|---|
| SVIR-01 | Extra Fine | 12 | |
| SVIR-02 | Mini | 12 | |
| SVIR-03 | Tough | 12 | |
| SVIR-04 | Wide | 6 | |
| ・It is a "removing felt-tip pen" which as same as our existing products "IMAGE REMOVER". ・Solvent Keshiron can be used into one pen using "Super Keshiron" "Safety Keshiron" "Super mild Keshiron" for different PS plate . ・Without using materials designated in the PRTR and Poisonous and Deleterious Substances Control Act. How to use ・Only by slightly depressing the tip of the Solvent Keshiron put on to the part you need to remove. Caution ・To prevent a dissolution accident, wipe it with the sponge which you soaked with water after removal. ・Use the "Silver Keshiron" when you use a paper plate. ・Use the "Gaining Keshiron" if you couldn't remove a part on a PS plate. |
|||
GRAINING IMAGE REMOVER "GRAINING KESHIRON"
 |
|||
| Order code No. | Package | ||
|---|---|---|---|
| GIR-1 | 1box | ||
| ・"GRANING IMAGE REMOVER" is easy to remove error parts on a long running PS plate. Without poisonous substances which we had to use so far. ・Without using materials designated in the PRTR and Poisonous and Deleterious Substances Control Act . How to use ・Soak the liquid which is attached to a pen point. Turn on a switch and put on a part you need to remove. Caution ・Wipe it with the sponge which you soaked with water after removal. ・ROTARY OF ELECTRIC MOTOR : 1 peace ・GRANING PEN POINT : 5 peaces ・GRANING LIQUID : 1 bottle (20cc) |
|||
SUPER IMAGE REMOVER
 |
|||
| Order code No. | Size | Package | |
|---|---|---|---|
| IRS-01 | Extra Fine(0.1mm) | 12 | |
| IRS-02 | Mini | 12 | |
| IRS-03 | Tough | 12 | |
| IRS-04 | Wide | 6 | |
| ・Proves efficiency in image removal off the PS metal plates, for both positive and negative. Also effective for the plates with UV ink. ・Gives no affection to the hydrophilic layer of the plates because of its weak acid content. ・Gives no harm to the anodic oxidation layer of the plates and no smudging. How to use ・After application to the unnecessary images, wipe off with wet cotton cloth or sponge before being dried. ・If unnecessary images still remain, repeat the above steps. Caution ・Keep out of reach of children. ・In case of skin contact, rinse off with flush water immediately. In case of eye contact, rinse off at once with flush water and go to see a doctor for medical treatment. ・Dispose of in accordance with the local, state and federal regulations. |
|||
SAFETY IMAGE REMOVER
 |
|||
| Order code No. | Size | Package | |
|---|---|---|---|
| SIR-01 | Mini | 12 | |
| SIR-02 | Tough | 12 | |
| SIR-03 | Micro point | 12 | |
| ・"Safety Image Remover" removes unnecessary images on positive P.S. metal plates. ・Lightly apply to the images to be removed on positive presensitized metal plates. ・For maintaining effective removal, wipe the remaining residue off the penpoint with a cloth. ・This pen does not contain hydrofluoric acid. |
|||
NEW IMAGE REMOVER
 |
|||
| Order code No. | Size | Package | |
|---|---|---|---|
| NIR-01 | Mini | 12 | |
| NIR-02 | Tough | 12 | |
IMAGE REMOVER PEN - BEAK
 |
||||
| Order code No. | Size | Package | ||
|---|---|---|---|---|
| IR-BE | Wide | 10 | ||
| ・IMAGE REMOVER PEN - BEAK was designed for the use on CTP plates of photopolymer, thermal, silver halide types and UV plates (both positive and negative PS metal plates). ・The pen point (oval cut) of Image Remover Pen - Beak will not be affected by the deletion fluid and is durable for long use. Also, it was designed for applying to the different sizes of the line or image to be removed in one pen. Caution ・The pen contains hydrofluoric acid. Avoid skin contact. In case of skin contact, flush with plenty of water immediately. In case of eye contact, rinse off at once with flush water and seek medical help. ・Be sure to close the cap tightly after use. |
||||
SCRATCH RECOVER PEN Wide point (15 mm)
| For recovering and saving the P.S. metal plate from scratch. It proves to be effective in devurring and preventing ink acceptance of scratched area and removes dirt on the plate edge. |
||||
 |
||||
| Order code No. | Size | Package | ||
|---|---|---|---|---|
| PS-DR | Regular | 12 | ||
| PS-DR-W | Wide | 6 | ||
| After application, wipe off with wet cotton cloth or sponge moistened with water and gumming. | ||||
SUPER MILD IMAGE REMOVER
 |
||||
| Order code No. | Size | Package | ||
|---|---|---|---|---|
| IRSM-01 | Mini | 12 | ||
| IRSM-02 | Tough | 12 | ||
| IRSM-03 | Wide | 6 | ||
|
・Super Mild Image Remover Pen does not contain chemicals applied to Japanese PRTR (Pollutant Release Transfer Register). ・Other feautures and usage are the same with the Super Image Remover Pen |
||||
IMAGE ADDITIONER
 |
||||
| Order code No. | Size | Package | ||
|---|---|---|---|---|
| IA-01 | Slim | 12 | ||
| IA-02 | G | 12 | ||
| IA-04 | Extara Fine | 12 | ||
PS MARK PEN Hard Resin Marker
|
PS Mark Pen proves to be effective in a check-marking for prevention of the slip-off in printing and adding line or correction of pin-holes on the presensitized metal plates. It is made from hard resin which makes a carving in the area where the ink is acceptable. However, it gives no damage to the blanket. |
||||
 |
||||
| Order code No. | Size | Package | ||
|---|---|---|---|---|
| PSM-01 | Fine | 6 | ||
| PSM-02 | Oval | 6 | ||
|
How to use ・Rub 5~6 times with the edge of the pen nib on the presensitized metal plate where you want to make a check-marking and add lines. ・The works are invisible because no lacquer comes out. If you wish easy finding of the area you used the pen, apply Image Additioner Pen that remains despite of using plate cleaner. ・For correction of pin-holes, use PS Mark Pen-Fine point (PSM-01) |
||||
